ADC sistemi
WindowsUpdated October 30, 2026

ADC
Smart Window

Smart window control with weather protection, developed and made in Slovenia. Here's everything you need to wire, set up and use the ADC Smart Window T010 controller day to day.

  • T010model
  • 230 V~power supply
  • ADC Homeapp
  • Wi-Fi + BTconnectivity

In about 10 minutes to a smart window: connection, test and calibration in the ADC Home app.

Get the ADC Home appApp StoreGoogle PlayAppGallery
The gold markers on the screenshots show where to tap. Click a screenshot to enlarge it and see what every button does.
The screenshots show the app in Slovenian. Buttons are in the same place in your language.

ADC Home app

Adding the ADC Smart Window controller

Before you start, have ready:

  • the password of your home 2.4 GHz Wi-Fi network (if Wi-Fi is not installed yet, do this step later),
  • a phone with Wi-Fi and mobile data switched on and location permission granted to the ADC Home app (Bluetooth is not needed for adding),
  • about 10 minutes.
The window actuator must already be connected according to the wiring diagram and its stroke must be set. The screenshots were taken on an iPhone; the screens in the Android app are the same.
A device can only be added on site, close to the controller. During adding, the phone connects directly to the controller's own Wi-Fi network, so adding from abroad or remotely is not possible. Once the device has been added, you can control it from anywhere.
  1. Add a new device

    On the home screen, tap “+” (Add) in the top right corner. The weather at the top shows zeros until you set your home location (next step).

    1. Tap + to add a device
  2. Set your home location

    When you add your first device, the app asks for your home location, which it uses for weather data. At home, tap the button to continue, use your current location and confirm it. You can change the location later in the menu. For a window this is especially important, because automatic closing in rain or wind is based on the weather data.

    The ADC Home app needs permission for precise location. If you declined it, turn it on in your phone settings, otherwise the current location will not work.
    1. 1Continue
    2. 2Use current location
    3. 3Confirm location
  3. Select the “Window” type

    In the list of device types, select “Window” and tap the button to continue.

    1. 1Select “Window”
    2. 2Confirm selection
  4. Connect the phone to the controller

    Tap the Wi-Fi settings button. In your phone settings, select the controller's network. Its name starts with “ADCWindow_”. The phone warns that the network has no internet or is not secure. This is expected. Then return to the ADC Home app. The cross (✗) in the app only means that the connection has not been established yet.

    1. 1Open Wi-Fi settings
    2. 2Select the ADCWindow_… network
    3. 3Return to the ADC Home app
  5. Check the connection

    Until the connection has been checked, a cross (✗) is shown. Tap the button to check the device connection. When a tick appears, the phone is connected to the controller. Tap the button to continue.

    1. 1Check the connection
    2. 2Continue
  6. Run the self-test

    At first, three dots (…) are shown on the screen. Tap the self-test button; the controller checks whether the window opens and closes. If the test succeeds, ticks appear next to both directions. If not, crosses (✗) appear: switch off the power, check the wiring against the diagram and repeat the test.

    During the self-test and calibration the window opens and closes by itself. Before you start, make sure there are no people, animals, hands or objects in the window opening or in the path of the sash.
    1. 1Start the self-test
    2. 2Repeat the test after checking the wiring
  7. Check the direction and switch type

    Use the Open and Close buttons to check the direction: with Open, the window must open. Under switch type, select whether a switch or a push button is connected. If the window or the switch works in the opposite direction, turn on the option to swap the motor or switch direction. No rewiring is needed. Then tap the button to continue.

    1. 1Select switch or push button
    2. 2Swap motor direction
    3. 3Swap switch direction
  8. Calibrate the device

    Tap the calibration button. The window opens and closes fully once and the controller learns both positions, so the stroke must already be set on the actuator. Wait for the tick, do not interrupt the calibration, then tap the button to continue. Without calibration the window does not work.

    The window also moves by itself during calibration. There must be no people, animals, hands or objects in the window opening or in the path of the sash.
    1. 1Start calibration
    2. 2Continue
  9. Connect the controller to your home Wi-Fi

    Choose your home 2.4 GHz Wi-Fi network and enter the password. The icon next to the network shows the actual signal strength at the controller's location. You can skip this step and do it later by adding the device again. For a window, a good signal is especially important, as automatic closing in rain needs the internet.

    Networks with the suffix “5G” and networks that use the same name for 2.4 and 5 GHz do not work; set a separate name for 2.4 GHz in your router. If the signal is weak, leave the box open and check the installation (Installation tab). If Wi-Fi is already running, do not skip this step during installation: only here do you see the real signal.
    1. 1Select your home Wi-Fi network
    2. 2Enter password
    3. 3Confirm
  10. Review the completed steps

    The app shows which steps have been completed. Tap the button to confirm. If you skipped a step, complete it by adding the device again from the beginning; the settings already made remain stored in the controller.

    For installers: Steps can be skipped; the settings are saved to the controller as you go. Use the self-test to check the wiring; calibration and the Wi-Fi connection can be done later. Without calibration the window does not work, so complete it before handing the device over.
    1. Confirm the review
  11. Name the device

    Enter a name, for example “Living room left”, and confirm it. Room first, then position, for example “Bedroom right”; this way you will find the device quickly even when you have several. If you cancel naming, a default name is used, which you can change later. The device then appears in the Devices list, where you can try it out straight away.

    1. 1Enter a name, e.g. “Living room left”
    2. 2Confirm the name
    3. 3Try it: open or close the window

When something goes wrong

Common problems when adding

The phone cannot find the “ADCWindow_…” network

Check that the controller is powered and that you are close to it. The network does not appear if the controller is already connected to Wi-Fi or added to another account. In that case a qualified electrician must reset it to factory settings: take the controller out of the box and, with power on, hold the button on the back for 3 seconds. Then delete the device in the app and add it again, because after a reset it stays in the account without a connection.

Back of the controller: the reset button. With power on, hold it with your finger for 3 seconds.
Back of the controller: the reset button. With power on, hold it with your finger for 3 seconds.
The device is always offline in the app

If the controller has been reset to factory settings, the device stays in the account but no longer works. Delete it in the device settings and add it again following this procedure.

Checking the device connection shows a cross

The phone has probably switched back to your home Wi-Fi by itself because the controller's network has no internet. In your phone settings, select the “ADCWindow_…” network again, return to the app and check the connection again.

The self-test shows crosses

The controller is most likely wired incorrectly. Check that the actuator wires are connected to the MOTOR ▲ and ▼ terminals and that the actuator's neutral wire is connected to the neutral wire of the installation. Switch off the power, check the wiring against the diagram and try again.

Calibration fails

Check that the stroke on the actuator is set correctly and that nothing obstructs the window along its path. Then repeat the calibration.

The controller does not connect to the home Wi-Fi

Make sure it is a 2.4 GHz network and that the password is correct. The controller does not connect to a network that uses the same name for 2.4 GHz and 5 GHz; set a separate 2.4 GHz network name in the router settings or contact your internet provider. If the signal is weak, check how the controller is installed (see the Installation tab, box “Most common cause of weak signal and failures”). You can also connect to the home Wi-Fi later by adding the device again; the other settings remain stored.

Next

Congratulations, your window is now smart

You can control it from anywhere. For a good start, set a ventilation position, add a schedule and switch on automatic closing in rain.

ADC Smart Window
ADC Smart WindowFresh air, whenever you need it.A smart window controller, designed and made in Slovenia.

Need help?

You're backed by our team in Kranj, who developed the system and make it. In your message, include the controller model and briefly describe the problem. You'll get a reply within 3 working days at most.

First check the tab Troubleshooting.

Write to us Book installationinfo@adcsmartsystems.com