ADC sistemi
ShadesUpdated October 30, 2026

ADC
Smart Shade PRO

Smart shade control with a magnetic opening sensor, developed and made in Slovenia. Here's everything you need to wire, set up and use the ADC Smart Shade PRO T010 controller day to day.

  • T010 PROmodel
  • 230 V~power supply
  • ADC Homeapp
  • Wi-Fi + BTconnectivity

For a qualified electrician: 9 steps to a correctly installed controller, with a check before closing the box.

Before you start

What you need

  • ControllerADC Smart Shade PRO T010
  • Shade motorsingle-phase 230 V~, with limit switches, up to 2 A
  • Deep boxdiameter and depth at least 60 mm
  • Wires and ferrules0.05–2.08 mm², ferrules for flexible wires
  • Magnetic sensornot included, with a two-core cable
  • Toolsscrewdriver and voltage tester
For setup
  • The ADC Home app and 2.4 GHz Wi-Fi (can also be connected later)
Optional
  • Up/down switch or push-button
  • Weather protection: wind or rain sensor, or weather data in the app
Before installation, switch off the mains fuse and use a voltage tester to check that the wires are dead. The device must be installed and maintained by a qualified electrician only.
For installers who know the older versions: the T010 controller has no N′ and L′ terminals. The motor neutral wire and the switch common are connected directly to the electrical installation, not to the controller.

Diagram

Wiring diagram

Wiring diagram ADC Smart Shade PRO
ADC Smart Shade PRO wiring diagram. Click the image to enlarge.
The wire colours in the diagram are for illustration only and do not show the actual wiring. Every motor manufacturer uses its own wire colours, so before connecting, check what each wire means in the motor manufacturer's instructions.

Terminal labels

Terminal markings on the T010 controller label.
Terminal markings on the T010 controller label.
Terminal labels: hover over or tap a label to see the terminal on the controller.
LInstallation phase
NInstallation neutral
STIKALO ▲Switch or push-button input, up
STIKALO ▼Switch or push-button input, down
MOTOR ▲Motor output, up
MOTOR ▼Motor output, down
MAGMagnetic sensor input (2 terminals, wire order does not matter)

Step by step

Installation procedure

  1. Set the motor end positions

    Set the upper and lower end positions of the shade on the motor according to the motor manufacturer's instructions, usually with a setting cable or a temporary switch. The controller does not set the end positions, it only learns them during calibration. Once they are set, continue with the connection.

  2. Switch off the power

    Remove the mains fuse for the shade circuit and use a tester to check that there is no voltage in the wires.

  3. Prepare the mounting location

    Install the controller in a deep electrical box or another suitable enclosure protected from moisture and water. Make sure no metal parts touch the terminals, as this can cause a short circuit. Nearby metal surfaces can also reduce the wireless signal range.

  4. Connect the motor

    Connect the motor's up wire to terminal MOTOR ▲ and the down wire to MOTOR ▼. Connect the motor neutral wire directly to the installation neutral (N), not to the controller. Connect the motor earth to the house earth.

    Connect only one motor to each controller. Connecting several motors in parallel to the same output can damage the motors and the controller. Take the neutral from the same circuit as the controller, otherwise the residual current device (RCD) may trip.
    Connect the motor
  5. Connect a switch or push-button (optional)

    Connect the switch common to the installation phase (L). Connect the switch's up output to terminal STIKALO ▲ and the down output to STIKALO ▼. Skip this step if the shades will be controlled only by phone or voice.

    Do not use illuminated switches or push-buttons (glow lamp or LED), as they can cause unintended movement. Connect the switch to a phase from the same circuit as the controller.
    Connect a switch or push-button (optional)
  6. Connect the magnetic sensor (optional)

    Mount the sensor on the frame of the window, door or shade and the magnet on the moving part, so that they are aligned in the closed position (gap according to the sensor manufacturer's instructions). Connect both sensor wires to the MAG terminals at the top of the controller. The order of the wires does not matter. Connect only the sensor contact to the MAG terminals, never a voltage. If you do not need the sensor, skip this step.

    Connect the magnetic sensor (optional)
  7. Connect the controller power supply

    Connect the installation phase to terminal L and the neutral wire to terminal N in the AC~ group.

    Connect the controller power supply
  8. Switch on the power and add the controller to the app

    After checking that everything is wired according to the diagram, insert the fuse. Add the controller to the ADC Home app following the instructions in the “Adding to the app” tab. In the step “Check the direction and switch type”, check the direction: pressing up must raise the shade. If it moves the wrong way, reverse the direction there, separately for the motor and for the switch, without rewiring. If you connected a sensor, open and close the window and check that the app shows the correct state.

  9. Check the installation and close the box

    Place the controller in the box as described below and check every item on the checklist. Close the box only once the Wi-Fi signal strength in the app is good (if Wi-Fi is already installed).

Installation

Correct installation in the box

Four conditions for a good signal and a long controller life. Most faults and warranty claims are caused by one of them.

Nothing over the controller
1

Nothing over the controller

Wires run downwards from the terminals, not over or around the controller. The box must not be crammed with wires of other circuits.

Label and terminals facing out
2

Label and terminals facing out

When you look into the open box, you must see the label and the terminals. The antenna is on this side.

Ferrules on flexible wires
3

Ferrules on flexible wires

Crimp a ferrule onto every flexible wire so that no strands stick out of the terminal and cause a short circuit.

No metal over the controller
4

No metal over the controller

Do not install the controller behind a metal switch frame, in a metal cabinet or in a roller shutter box. Metal blocks the signal. If the switch is in the same box, use a double box: the switch in one part, the controller in the other.

Damage caused by incorrect installation, such as an overcrowded box, a short circuit between protruding strands, mechanical damage, moisture or wiring not in accordance with these instructions, is not covered by the warranty.

Checklist

Before closing the box

Before you close the box, check every point. Tap a point to tick it.

0 / 7

Safety

  • Do not connect loads that exceed the controller's rated values.
  • Install the device strictly according to the wiring diagram. Incorrect connections are dangerous and can damage the device.
  • The controller must be installed so that it is protected from unauthorised access and harmful influences.

Leave the installation to us

Don't have an electrician? Our specialists take care of the electrical connection, Wi-Fi setup, app configuration and testing, and show you how to use the device.

Book installation

Downloads

Wiring diagram, terminal labels and technical data on one A4 page, for installers and planners.

ADC Smart Shade PRO
ADC Smart Shade PROLight, just the way you want it.
And you always know what is open.
A smart shade controller with a magnetic sensor, designed and made in Slovenia.

Need help?

You're backed by our team in Kranj, who developed the system and make it. In your message, include the controller model and briefly describe the problem. You'll get a reply within 3 working days at most.

First check the tab Troubleshooting.

Write to us Book installationinfo@adcsmartsystems.com