ADC sistemi
ShadesUpdated October 30, 2026

ADC
Smart Shade

Smart shade control, developed and made in Slovenia. Here's everything you need to wire, set up and use the ADC Smart Shade T010 controller day to day.

  • T010model
  • 230 V~power supply
  • ADC Homeapp
  • Wi-Fi + BTconnectivity

For a qualified electrician: 8 steps to a correctly installed controller, with a check before closing the box.

Before you start

What you need

  • ControllerADC Smart Shade T010
  • Shade motorsingle-phase 230 V~, with limit switches, up to 2 A
  • Deep boxdiameter and depth at least 60 mm
  • Wirescross-section 0.05–2.08 mm² (30–14 AWG)
  • Ferrulesfor flexible wires, with a crimping tool
  • Toolsscrewdriver and voltage tester
For setup
  • The ADC Home app and 2.4 GHz Wi-Fi (can also be connected later)
Optional
  • Up/down switch or push-button
  • Weather protection: wind or rain sensor, or weather data in the app
Before installation, switch off the mains fuse and use a voltage tester to check that the wires are dead. The device must be installed and maintained by a qualified electrician only.

Diagram

Wiring diagram

Wiring diagram ADC Smart Shade
ADC Smart Shade T010 wiring diagram. Click the image to enlarge.
The wire colours in the diagram are for illustration only and do not show the actual wiring. Every motor manufacturer uses its own wire colours, so before connecting, check what each wire means in the motor manufacturer's instructions.

Terminal labels

Terminal markings on the T010 controller label.
Terminal markings on the T010 controller label.
Terminal labels: hover over or tap a label to see the terminal on the controller.
LInstallation phase
NInstallation neutral
STIKALO ▲Switch or push-button input, up
STIKALO ▼Switch or push-button input, down
MOTOR ▲Motor output, up
MOTOR ▼Motor output, down

Step by step

Installation procedure

  1. Set the motor end positions

    Set the upper and lower end positions of the shade on the motor according to the motor manufacturer's instructions, usually with a setting cable or a temporary switch. The controller does not set the end positions, it only learns them during calibration. Once they are set, continue with the connection.

  2. Switch off the power

    Remove the mains fuse for the shade circuit and use a tester to check that there is no voltage in the wires.

  3. Prepare the mounting location

    Install the controller in a deep electrical box or another suitable enclosure protected from moisture and water. Make sure no metal parts touch the terminals, as this can cause a short circuit. Nearby metal surfaces can also reduce the wireless signal range.

  4. Connect the motor

    Connect the motor's up wire to terminal MOTOR ▲ and the down wire to MOTOR ▼. Connect the motor neutral wire directly to the installation neutral (N), not to the controller. Connect the motor earth to the house earth.

    Connect only one motor to each controller. Connecting several motors in parallel to the same output can damage the motors and the controller. Take the neutral from the same circuit as the controller, otherwise the residual current device (RCD) may trip.
    Connect the motor
  5. Connect a switch or push-button (optional)

    Connect the switch common to the installation phase (L). Connect the switch's up output to terminal STIKALO ▲ and the down output to STIKALO ▼. Skip this step if the shades will be controlled only by phone or voice.

    Do not use illuminated switches or push-buttons (glow lamp or LED), as they can cause unintended movement. Connect the switch to a phase from the same circuit as the controller.
    Connect a switch or push-button (optional)
  6. Connect the controller power supply

    Connect the installation phase to terminal L and the neutral wire to terminal N in the AC~ group.

    Connect the controller power supply
  7. Switch on the power and add the controller to the app

    After checking that everything is wired according to the diagram, insert the fuse. Add the controller to the ADC Home app following the instructions in the “Adding to the app” tab. In the step “Check the direction and switch type”, check the direction: pressing up must raise the shade. If it moves the wrong way, reverse the direction there, separately for the motor and for the switch, without rewiring.

  8. Check the installation and close the box

    Place the controller in the box as described below and check every item on the checklist. Close the box only once the Wi-Fi signal strength in the app is good (if Wi-Fi is already installed).

Installation

Correct installation in the box

Four conditions for a good signal and a long controller life. Most faults and warranty claims are caused by one of them.

Nothing over the controller
1

Nothing over the controller

Wires run downwards from the terminals, not over or around the controller. The box must not be crammed with wires of other circuits.

Label and terminals facing out
2

Label and terminals facing out

When you look into the open box, you must see the label and the terminals. The antenna is on this side.

Ferrules on flexible wires
3

Ferrules on flexible wires

Crimp a ferrule onto every flexible wire so that no strands stick out of the terminal and cause a short circuit.

No metal over the controller
4

No metal over the controller

Do not install the controller behind a metal switch frame, in a metal cabinet or in a roller shutter box. Metal blocks the signal. If the switch is in the same box, use a double box: the switch in one part, the controller in the other.

Damage caused by incorrect installation, such as an overcrowded box, a short circuit between protruding strands, mechanical damage, moisture or wiring not in accordance with these instructions, is not covered by the warranty.

Checklist

Before closing the box

Before you close the box, check every point. Tap a point to tick it.

0 / 7
Do you have an older version (T001, T003, T004)?

Older versions of the Smart Shade controller are wired differently. The model is printed on the label on the front of the controller. Their instructions are below.

For installers who know the older versions: the T010 controller has no N′ and L′ terminals. The motor neutral wire and the switch common are connected directly to the electrical installation, not to the controller.

What you need

  • ADC Smart Shade controller
  • Single-phase shade motor up to 500 W with electronic or mechanical limit switches
  • Deep electrical box Ø ≥ 60 mm, depth ≥ 60 mm (deep or double)
  • Wires with a cross-section of 0.4 mm² to 0.8 mm²
  • Up/down switch or push-button (optional)
  • 2.4 GHz Wi-Fi network and the ADC Home app

Installation procedure

  1. Switch off the power

    Remove the mains fuse for the shade circuit and use a tester to check that there is no voltage in the wires.

  2. Prepare the mounting location

    Install the controller in a deep electrical box or another suitable enclosure protected from moisture and water. Make sure no metal parts touch the terminals, as this can cause a short circuit. Nearby metal surfaces can also reduce the wireless signal range.

  3. Connect the motor

    Connect the motor's neutral wire to terminal N′, the up wire to ▲ and the down wire to ▼. Connect the motor earth to the building earth. Connect only one motor to each controller. Connecting several motors in parallel to the same output can damage the motors and the controller.

  4. Connect a switch or push-button (optional)

    Connect the switch control phase to L′ and the up and down wires to ▲ and ▼ in the SWITCH group. Skip this step if the shades will be controlled only by phone or voice.

  5. Connect the power supply

    Finally, connect the supply phase to L and the neutral wire to N.

  6. Switch on the power

    After checking that everything is wired according to the diagram, insert the fuse. The controller is ready to be added to the app.

  7. Set the end positions and check the direction

    First set the upper and lower end positions of the blind on the motor according to the motor manufacturer's instructions, as the controller does not set them. Then add the controller to the ADC Home app and check the direction in the step “Check the direction and switch type”: pressing up must raise the blind. If it moves the wrong way, reverse the direction there, separately for the motor and for the switch, without rewiring. Run the calibration in the app only after the end positions are set, because the controller learns the end positions during calibration.

Wiring diagram

Wiring diagram ADC Smart Shade
T001, T003, T004

Terminal labels

LSupply phase
NSupply neutral
▲Motor: up
▼Motor: down
N′Motor neutral wire (mandatory)
L′Switch control phase (mandatory if a switch is connected)
▼Switch: down
▲Switch: up

Safety

  • Do not connect loads that exceed the controller's rated values.
  • Install the device strictly according to the wiring diagram. Incorrect connections are dangerous and can damage the device.
  • The controller must be installed so that it is protected from unauthorised access and harmful influences.

Leave the installation to us

Don't have an electrician? Our specialists take care of the electrical connection, Wi-Fi setup, app configuration and testing, and show you how to use the device.

Book installation

Downloads

Wiring diagram, terminal labels and technical data on one A4 page, for installers and planners.

ADC Smart Shade
ADC Smart ShadeLight, just the way you want it.A smart shade controller, designed and made in Slovenia.

Need help?

You're backed by our team in Kranj, who developed the system and make it. In your message, include the controller model and briefly describe the problem. You'll get a reply within 3 working days at most.

First check the tab Troubleshooting.

Write to us Book installationinfo@adcsmartsystems.com