Answers to the most common questions. If you can't find a solution, write to us.
Support
Troubleshooting
Can I add a device remotely?
No. You can only add a device on site, close to the controller, because during setup the phone connects directly to the controller's Wi-Fi network. Set the home location while you are at home too, as the app uses the phone's current location. Once the device has been added, you can control it from anywhere.
The controller will not connect to Wi-Fi
Check that the network is 2.4 GHz, that the password is correct and that the controller is not surrounded by metal that weakens the signal. The app shows the signal strength while adding the device. You can also connect to home Wi-Fi later; meanwhile the controller works locally via Bluetooth.
The device is shown as unreachable in the app
The controller has no internet connection; the app shows an exclamation mark (!) in front of the device icon. Check that it has power and that your home Wi-Fi works. The connection icon on the detail screen shows whether the controller communicates via the cloud (CLOUD) or locally via Bluetooth (LOCAL). Scenes are stored on the controller and work without internet, except weather scenes.
The self-test in the app failed
The controller is most likely wired incorrectly. Check that the motor wires are connected to terminals MOTOR ▲ and ▼ (not STIKALO) and that the motor neutral wire is connected to the installation neutral. Switch off the power, check the wiring against the diagram and try again.
Calibration fails
Check that both end positions are set correctly on the motor and that nothing obstructs the shade along its path. Then repeat the calibration (Settings → Recalibrate).
The shade moves in the wrong direction
You can reverse the direction in the app: in the shade settings choose “Swap direction” and reverse the motor, the switch or both. No rewiring is needed.
The wall switch does not work or moves the wrong way
In the settings, check the switch type (switch or push button) and, if needed, turn on the option to swap the switch direction. If the switch does not work at all, check the wiring: switch common to phase L, up and down to terminals STIKALO ▲ and ▼.
The shade stops early or does not travel all the way
Calibrate the device again (Settings → Recalibrate). Also check that the motor end positions have not changed and that nothing obstructs the shade along its path.
The shade does not respond in the app
Check whether a scene with smart weather data is active. When a weather condition is met (for example strong wind), manual control in the app is disabled for safety and other scenes do not run. A wall switch or push-button overrides the weather condition for 30 seconds.
The shade moves on its own
Most likely a scenario has run: a schedule, sunrise or sunset, or weather protection. Check your scenarios in the ADC Home app on the Scenarios tab. The shade can also be moved by another user you share the device with. You can see who moved it and when under Settings → History. If an illuminated switch or push-button is connected, replace it with a standard one.
How do I control several shades at once?
In the ADC Home app, on the Groups tab, combine several devices into a group, for example all shades in the living room, and control them with one tap. You can also move several shades at once with scenarios.
Can I control the shade by voice?
Yes, with Amazon Alexa and Google Home. Siri is not supported.
The “Favourite” position does not appear on another phone
The “Favourite” and “Ventilation” positions are stored on the phone where you set them. Each household member sets them on their own phone.
What happens during a power or internet outage?
During a power outage the shade does not work; when power returns, the controller carries on with the same settings. During an internet outage remote control does not work, but the wall switch and Bluetooth control nearby still work. Scenarios are stored on the controller and work without internet, except weather scenarios.
How do I reset the controller to factory settings?
There is a small opening with a button on the back of the controller. With the controller powered, hold the button for 3 seconds. As the button is on the back, the controller has to be taken out of the box for this. All settings will be erased. Only a trained installer should press the button, as the device is live.

Where can I find the EU declaration of conformity?
We will send you the declaration of conformity on request. Write to us at info@adcsmartsystems.com.

Need help?
You're backed by our team in Kranj, who developed the system and make it. In your message, include the controller model and briefly describe the problem. You'll get a reply within 3 working days at most.
Write to us Book installationinfo@adcsmartsystems.com