For a qualified electrician: 9 steps to a correctly installed controller, with a check before closing the box.
Before you start
What you need
- ControllerADC Smart Window PRO T010
- Window actuator230 V~, chain or spindle, with limit switches, up to 2 A
- Deep boxdiameter and depth at least 60 mm
- Wires and ferrules0.05–2.08 mm², ferrules for flexible wires
- Magnetic sensornot included, with a two-core cable
- Toolsscrewdriver and voltage tester
- The ADC Home app and 2.4 GHz Wi-Fi (can also be connected later)
- Switch or push-button for opening and closing
- Closing in rain or wind: wind or rain sensor, or weather data in the app
Diagram
Wiring diagram
Terminal labels

Terminal labels: hover over or tap a label to see the terminal on the controller.
LInstallation phaseNInstallation neutralSTIKALO ▲Switch or push-button input, openingSTIKALO ▼Switch or push-button input, closingMOTOR ▲Actuator output, openingMOTOR ▼Actuator output, closingMAGMagnetic sensor input (2 terminals, wire order does not matter)Step by step
Installation procedure
Set the actuator stroke
Set the open and closed position of the window (stroke) on the actuator according to the manufacturer's instructions, usually with a setting cable or a temporary switch. The controller does not set the end positions, it only learns them during calibration. Once the stroke is set, continue with the connection.
Switch off the power
Remove the mains fuse for the window actuator circuit and use a tester to check that there is no voltage in the wires.
Prepare the mounting location
Install the controller in a deep electrical box or another suitable enclosure protected from moisture and water. Make sure no metal parts touch the terminals, as this can cause a short circuit. Nearby metal surfaces can also reduce the wireless signal range.
Connect the actuator
Connect the actuator's opening wire to the MOTOR ▲ terminal and its closing wire to MOTOR ▼. Connect the actuator's neutral wire directly to the neutral wire of the installation (N), not to the controller. Connect the actuator's earth to the building earth.
Connect only one actuator per controller. Connecting several actuators in parallel to the same output can damage the actuators and the controller. Take the neutral from the same circuit as the controller, otherwise the residual current device (RCD) may trip.
Connect a switch or push-button (optional)
Connect the common terminal of the switch to the phase of the installation (L). Connect the switch output for opening to the STIKALO ▲ terminal and the output for closing to STIKALO ▼. If you will control the window only by phone or voice, skip this step.
Do not use illuminated switches or push-buttons (glow lamp or LED), as they can cause unintended movement. Connect the switch to a phase from the same circuit as the controller.
Connect the magnetic sensor (optional)
Mount the sensor on the window frame and the magnet on the sash, so that they are aligned in the closed position (gap according to the sensor manufacturer's instructions). Connect both sensor wires to the MAG terminals at the top of the controller. The order of the wires does not matter. Connect only the sensor contact to the MAG terminals, never a voltage. If you do not need the sensor, skip this step.

Connect the controller power supply
Connect the installation phase to terminal L and the neutral wire to terminal N in the AC~ group.

Switch on the power and add the controller to the app
After checking that everything is wired according to the diagram, insert the fuse. Add the controller to the ADC Home app following the instructions in the “Adding to the app” tab. While adding it, check the direction: pressing Open must open the window. If it moves the wrong way, reverse the direction in the app, separately for the actuator and for the switch, without rewiring. If you connected a sensor, open and close the window and check that the app shows the correct state.
Check the installation and close the box
Place the controller in the box as described below and check every item on the checklist. Close the box only once the Wi-Fi signal strength in the app is good (if Wi-Fi is already installed).
Installation
Correct installation in the box
Four conditions for a good signal and a long controller life. Most faults and warranty claims are caused by one of them.
Nothing over the controller
Wires run downwards from the terminals, not over or around the controller. The box must not be crammed with wires of other circuits.
Label and terminals facing out
When you look into the open box, you must see the label and the terminals. The antenna is on this side.
Ferrules on flexible wires
Crimp a ferrule onto every flexible wire so that no strands stick out of the terminal and cause a short circuit.
No metal over the controller
Do not install the controller behind a metal switch frame, in a metal cabinet or in a roller shutter box. Metal blocks the signal. If the switch is in the same box, use a double box: the switch in one part, the controller in the other.
Damage caused by incorrect installation, such as an overcrowded box, a short circuit between protruding strands, mechanical damage, moisture or wiring not in accordance with these instructions, is not covered by the warranty.
Checklist
Before closing the box
Before you close the box, check every point. Tap a point to tick it.
Safety
- Do not connect loads that exceed the controller's rated values.
- Install the device strictly according to the wiring diagram. Incorrect connections are dangerous and can damage the device.
- The controller must be installed so that it is protected from unauthorised access and harmful influences.
Leave the installation to us
Don't have an electrician? Our specialists take care of the electrical connection, Wi-Fi setup, app configuration and testing, and show you how to use the device.
Book installationDownloads
Wiring diagram, terminal labels and technical data on one A4 page, for installers and planners.

And peace of mind when you are away.A smart window controller with opening detection and notifications, designed and made in Slovenia.
Need help?
You're backed by our team in Kranj, who developed the system and make it. In your message, include the controller model and briefly describe the problem. You'll get a reply within 3 working days at most.
First check the tab Troubleshooting.
Write to us Book installationinfo@adcsmartsystems.com