Answers to the most common questions. If you can't find a solution, write to us.
Support
Troubleshooting
Can I add a device remotely?
No. You can only add a device on site, close to the controller, because during setup the phone connects directly to the controller's Wi-Fi network. Set the home location while you are at home too, as the app uses the phone's current location. Once the device has been added, you can control it from anywhere.
The controller will not connect to Wi-Fi
Check that the network is 2.4 GHz, that the password is correct and that the controller is not surrounded by metal that weakens the signal. The app shows the signal strength while adding the device. You can also connect to home Wi-Fi later; meanwhile the controller works locally via Bluetooth.
The device is shown as unreachable in the app
The controller has no internet connection; the app shows an exclamation mark (!) in front of the device icon. Check that it has power and that your home Wi-Fi works. The connection icon on the detail screen shows whether the controller communicates via the cloud (CLOUD) or locally via Bluetooth (LOCAL). Scenes are stored on the controller and work without internet, except weather scenes.
The self-test in the app failed
The controller is most likely wired incorrectly. Check that the actuator wires are connected to the MOTOR ▲ and ▼ terminals (not to STIKALO) and that the actuator's neutral wire is connected to the neutral wire of the installation. Switch off the power, check the wiring against the diagram and try again.
Calibration fails
Check that the actuator stroke is set correctly, that its built-in limit switches work and that nothing obstructs the window along its path. Then repeat the calibration (Settings → Recalibrate).
The window moves in the wrong direction
You can reverse the direction in the app, separately for the actuator and for the switch. There is no need to rewire.
The wall switch does not work or moves the wrong way
In the settings, check the switch type (switch or push-button) and reverse the switch direction if needed. If the switch does not work at all, check the wiring: the switch common to phase L, opening and closing to the STIKALO ▲ and ▼ terminals.
The window stops early or does not close fully
Recalibrate the device in the device settings. Also check that the stroke on the actuator has not changed and that nothing obstructs the window's movement.
The window does not respond in the app
Check whether a scenario with smart weather data or a sensor is active. When the weather condition is met (for example rain or strong wind), manual opening in the app is disabled for safety and other scenarios do not run. The wall switch or push-button overrides the weather condition for 30 seconds.
The window opens or closes on its own
Most likely a scenario has run: a schedule or weather protection for rain or wind. Check your scenarios in the ADC Home app on the Scenarios tab. The window can also be moved by another user you share the device with. You can see who moved it and when under Settings → History. If an illuminated switch or push-button is connected, replace it with a standard one.
The window did not close automatically in rain or wind
Automatic closing works only if a weather scenario is set up in the app, using smart weather data for your location (subscription in the app) or your own wind sensor, rain sensor or weather station. Smart weather data requires the controller to be connected to the internet. Check that the scenario is switched on and that the device is reachable in the app.
The app shows the wrong state (open or closed)
Check that the sensor and magnet are aligned and close enough together in the closed position, and that both wires are firmly screwed into the MAG terminals. The sensor must be closed when the window is closed. A sensor that works the other way round shows the opposite state.
I do not get a notification when the window opens
Check that the ADC Home app is allowed to send notifications in your phone settings and that the phone is connected to the internet. Also check whether the sensor state in the app changes when you open the window.
How do I control several windows at once?
In the ADC Home app, on the Groups tab, combine several devices into a group, for example all roof windows, and control them with one tap. You can also move several windows at once with scenarios.
Can I control the window by voice?
Yes, with Amazon Alexa and Google Home. Siri is not supported.
The “Favourite” position does not appear on another phone
The “Favourite” and “Ventilation” positions are stored on the phone where you set them. Each household member sets them on their own phone.
What happens during a power or internet outage?
During a power outage the window stays in its current position; when power returns, the controller continues with the same settings. During an internet outage, remote control and scenarios with smart weather data do not work, so the window will not close automatically when it rains. The wall switch and Bluetooth control nearby still work.
How do I reset the controller to factory settings?
There is a small opening with a button on the back of the controller. With the controller powered, hold the button for 3 seconds. As the button is on the back, the controller has to be taken out of the box for this. All settings will be erased. Only a trained installer should press the button, as the device is live.

Where can I find the EU declaration of conformity?
We will send you the declaration of conformity on request. Write to us at info@adcsmartsystems.com.

And peace of mind when you are away.A smart window controller with opening detection and notifications, designed and made in Slovenia.
Need help?
You're backed by our team in Kranj, who developed the system and make it. In your message, include the controller model and briefly describe the problem. You'll get a reply within 3 working days at most.
Write to us Book installationinfo@adcsmartsystems.com