ADC sistemi
ShadesUpdated October 30, 2026

ADC
Smart Shade

Smart shade control, developed and made in Slovenia. Here's everything you need to wire, set up and use the ADC Smart Shade T010 controller day to day.

  • T010model
  • 230 V~power supply
  • ADC Homeapp
  • Wi-Fi + BTconnectivity

Fine-tune how it works: favourite positions, direction, switch type and calibration.

The gold markers on the screenshots show where to tap. Click a screenshot to enlarge it and see what every button does.
The screenshots show the app in Slovenian. Buttons are in the same place in your language.

Shade settings

Settings overview

Open the settings with the gear in the top right of the shade detail screen. They are divided into three groups, the same as below: Favourites, Shade (in the app this group is named after the shade type, for example Venetian blind) and Controller. After each change the app confirms that the device has been updated successfully; tap OK. Tap a setting below for a description.

  1. 1Tap the gear for settings
  2. 2Close the message

Settings

Favourites

Two saved positions you can move the shade to with one tap, using the Favourite and Ventilation buttons on the shade detail screen (see the Use tab). They are stored on the phone, so each phone has its own positions, and you set them again when you change phones.

Favourite

Move the shade to the desired position with your finger or use Open or Close. For a venetian blind, also set the tilt with the button in the bottom right. Tap Save and confirm with OK. The position is saved on the phone.

  1. 1Save the position
  2. 2Fully open
  3. 3Fully closed
  4. 4Set the position with your finger
  5. 5Slat tilt (venetian blind)
  6. 6Confirm
Ventilation

Works the same as Favourite: set a position for airing, tap Save and confirm with OK. This position is also saved on the phone.

  1. 1Save the position
  2. 2Fully open
  3. 3Fully closed
  4. 4Set the position with your finger
  5. 5Slat tilt (venetian blind)
  6. 6Confirm

Settings

Shade

Settings for the shade and the motor. They apply to the device, so all users see the change.

Rename

Enter a new name and tap Confirm. The Confirm button becomes active once you change the name. Keep the name short: room first, then position, for example “Living room balcony”.

  1. 1Enter a new name
  2. 2Confirm the name
Recalibrate

Runs the calibration again, for example after replacing the motor or changing the limit switches. Confirm with Yes. During calibration the shade moves by itself, so there must be no people, animals or objects under it or in its path.

  1. Confirm calibration
Shade type

Select a new type: roller shutter, venetian blind, screen, awning, insect screen or pergola. The list scrolls, so you will find the last types further down. If you select a venetian blind, Tilt time and Tilt type also appear in the settings.

  1. 1Select the shade type
  2. 2The list continues: awning, insect screen, pergola
Reverse direction

Select what is reversed. If the shade moves the wrong way from both the app and the wall switch, select Motor. If the app works correctly but the switch works the opposite way, select Switch. If it moves the wrong way from the app but correctly from the switch, select Both. No rewiring is needed.

  1. 1Motor direction reversed
  2. 2Switch direction reversed
  3. 3Both directions reversed
Switch type

Select what is connected on the wall: a switch stays in the pressed position, a push-button springs back after pressing. With a push-button, if you press up or down twice in a row, the shade keeps moving in that direction until you stop it or it reaches the end position.

  1. 1A switch is connected
  2. 2A push-button is connected
Tilt time

This setting only appears for a venetian blind. The tilt time is the time the slats need to change their tilt. Enter it in milliseconds (1000 ms = 1 s) and tap Confirm. Guide values: about 1250 ms for a 90° tilt and about 2500 ms for 180°. The exact time depends on the motor, so adjust the value if needed.

  1. 1Enter a new time (1000 ms = 1 s)
  2. 2Confirm
Tilt type

This setting only appears for a venetian blind. Select the tilt type: lower 90°, upper 90° or full 180°. The type depends on the kind of venetian blind; you can get this information from the blind manufacturer.

  1. 1Lower 90°
  2. 2Upper 90°
  3. 3Full 180°
History

Shows who moved the shade and when, and to which position and tilt.

Settings

Controller

Restarting and removing the device.

Deleting a device cannot be undone. The device is also removed for all other users who have access to it, and its history is deleted. To add it again, you must be on site, close to the controller.
Restart device

Restarts the controller, for example if the device does not respond. The settings remain saved. You can restart it yourself. Confirm with Yes.

  1. Confirm the restart
Delete device

Removes the device from the app. Confirm with Yes. Also delete the device if the controller has been reset to factory settings, then add it again.

  1. Confirm deletion

Next

What's next?

ADC Smart Shade
ADC Smart ShadeLight, just the way you want it.A smart shade controller, designed and made in Slovenia.

Need help?

You're backed by our team in Kranj, who developed the system and make it. In your message, include the controller model and briefly describe the problem. You'll get a reply within 3 working days at most.

First check the tab Troubleshooting.

Write to us Book installationinfo@adcsmartsystems.com